ip
ipku.in

IPv4 Subnet Calculator

Enter an IP with a CIDR prefix or a subnet mask to see its network, broadcast, host range, and host count. You can also split the network into smaller subnets.

$ ipcalc
private IP (RFC 1918)10.84.72.0/22
network10.84.72.0/22
broadcast10.84.75.255
first host10.84.72.1
last host10.84.75.254
subnet mask255.255.252.0
wildcard0.0.3.255
addresses1,024
usable hosts1,022
classA
ipcalc 10.84.72.0/22
address00001010.01010100.01001000.00000000
subnet mask11111111.11111111.11111100.00000000
network00001010.01010100.01001000.00000000
broadcast00001010.01010100.01001011.11111111
green = network part, grey = host part
hex0x0a544800
decimal173295616
reverse dns0.72.84.10.in-addr.arpa
ipv4-mapped::ffff:a54:4800

/22 split into /27 · 32 subnets

close ×
#networkhost rangebroadcast
110.84.72.0/2710.84.72.1 – 10.84.72.3010.84.72.31
210.84.72.32/2710.84.72.33 – 10.84.72.6210.84.72.63
310.84.72.64/2710.84.72.65 – 10.84.72.9410.84.72.95
410.84.72.96/2710.84.72.97 – 10.84.72.12610.84.72.127
510.84.72.128/2710.84.72.129 – 10.84.72.15810.84.72.159
610.84.72.160/2710.84.72.161 – 10.84.72.19010.84.72.191
710.84.72.192/2710.84.72.193 – 10.84.72.22210.84.72.223
810.84.72.224/2710.84.72.225 – 10.84.72.25410.84.72.255
910.84.73.0/2710.84.73.1 – 10.84.73.3010.84.73.31
1010.84.73.32/2710.84.73.33 – 10.84.73.6210.84.73.63
1110.84.73.64/2710.84.73.65 – 10.84.73.9410.84.73.95
1210.84.73.96/2710.84.73.97 – 10.84.73.12610.84.73.127
1310.84.73.128/2710.84.73.129 – 10.84.73.15810.84.73.159
1410.84.73.160/2710.84.73.161 – 10.84.73.19010.84.73.191
1510.84.73.192/2710.84.73.193 – 10.84.73.22210.84.73.223
1610.84.73.224/2710.84.73.225 – 10.84.73.25410.84.73.255
1710.84.74.0/2710.84.74.1 – 10.84.74.3010.84.74.31
1810.84.74.32/2710.84.74.33 – 10.84.74.6210.84.74.63
1910.84.74.64/2710.84.74.65 – 10.84.74.9410.84.74.95
2010.84.74.96/2710.84.74.97 – 10.84.74.12610.84.74.127
2110.84.74.128/2710.84.74.129 – 10.84.74.15810.84.74.159
2210.84.74.160/2710.84.74.161 – 10.84.74.19010.84.74.191
2310.84.74.192/2710.84.74.193 – 10.84.74.22210.84.74.223
2410.84.74.224/2710.84.74.225 – 10.84.74.25410.84.74.255
2510.84.75.0/2710.84.75.1 – 10.84.75.3010.84.75.31
2610.84.75.32/2710.84.75.33 – 10.84.75.6210.84.75.63
2710.84.75.64/2710.84.75.65 – 10.84.75.9410.84.75.95
2810.84.75.96/2710.84.75.97 – 10.84.75.12610.84.75.127
2910.84.75.128/2710.84.75.129 – 10.84.75.15810.84.75.159
3010.84.75.160/2710.84.75.161 – 10.84.75.19010.84.75.191
3110.84.75.192/2710.84.75.193 – 10.84.75.22210.84.75.223
3210.84.75.224/2710.84.75.225 – 10.84.75.25410.84.75.255
01 / table

IPv4 CIDR prefix table.

Click a prefix longer than your network to split it into subnets.

prefixsubnet maskaddresseshostsin your /22
/00.0.0.04,294,967,2964,294,967,294-
/1128.0.0.02,147,483,6482,147,483,646-
/2192.0.0.01,073,741,8241,073,741,822-
/3224.0.0.0536,870,912536,870,910-
/4240.0.0.0268,435,456268,435,454-
/5248.0.0.0134,217,728134,217,726-
/6252.0.0.067,108,86467,108,862-
/7254.0.0.033,554,43233,554,430-
/8255.0.0.016,777,21616,777,214-
/9255.128.0.08,388,6088,388,606-
/10255.192.0.04,194,3044,194,302-
/11255.224.0.02,097,1522,097,150-
/12255.240.0.01,048,5761,048,574-
/13255.248.0.0524,288524,286-
/14255.252.0.0262,144262,142-
/15255.254.0.0131,072131,070-
/16255.255.0.065,53665,534-
/17255.255.128.032,76832,766-
/18255.255.192.016,38416,382-
/19255.255.224.08,1928,190-
/20255.255.240.04,0964,094-
/21255.255.248.02,0482,046-
/22255.255.252.01,0241,0221
/23255.255.254.05125102 split →
/24255.255.255.02562544 split →
/25255.255.255.1281281268 split →
/26255.255.255.192646216 split →
/27255.255.255.224323032 split →
/28255.255.255.240161464 split →
/29255.255.255.24886128 split →
/30255.255.255.25242256 split →
/31255.255.255.25422512 split →
/32255.255.255.255111,024 split →
02 / faq

About this calculator.

How do I use this subnet calculator?

▼

Type an IP address followed by a prefix, like 192.168.1.10/24, or by a subnet mask, like 192.168.1.10 255.255.255.0. Without a prefix it uses /24. Click a row in the table to split the network into smaller subnets.

Why are usable hosts always 2 fewer?

▼

The first address in a subnet is the network address and the last is the broadcast address, so neither can go to a device. The exceptions are /31 (point-to-point links, RFC 3021) and /32 (a single address), which use every address.

Can I use it from a terminal?

▼

Yes. curl 'ipku.in/en/tools/ipv4-subnet-calculator?q=192.168.1.10/24' returns the result as plain text.

Learn how to work it out →